lock Warranty Information keyboard_arrow_down
Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.
WARRANTY:
Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.
Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.
If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.
Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)
Moog Tie Rods
Connecting the Driver to the Vehicle
Tie rods are a crucial part of your steering system. When you turn your steering wheel the motion travels through the steering rack, through the tie rods, and finally through your steering arm or spindle. Without tie rods, you wouldn't be able to turn your car. This part is also incredibly important to your vehicle's alignment. If you replace your tie rods, make sure to get an alignment done immediately afterward.
Designed for Strength, Durability, and Longevity
Moog tie rods feature several differences from the OE. One of the more obvious differences is the overall design itself. Whereas many OE tie rods are two-piece assemblies, Moog's tie rods are forged one-piece units. This one-piece design reduces the chance of early wear, increasing the durability of the part as a whole. To protect your tie rod, Moog uses a neoprene-sealed rubber dust boot. This dust boot is resistant to both extreme temperatures and abrasion. The design for this rubber boot includes a small valve to allow for the flushing of old grease and contaminants. In addition to all these other features, Moog crafts their tie rod end using hardened full-ball metal studs. These hardened studs can stand up to much more than the OE, making the tie rod that much more dependable.
Product Reviews for moog-es3493t | Front Outer Tie Rod | 02-06 Cadillac Escalade | MOOG
- 5 Star (2)
-
-
- 100%
-
- 4 Star (0)
-
-
- 0%
-
- 3 Star (0)
-
-
- 0%
-
- 2 Star (0)
-
-
- 0%
-
- 1 Star (0)
-
-
- 0%
-
MOOG moog-es3493t
starstarstarstarstar" Review 1 Year Later "
Couldnt be happier with all the parts including this one I purchased to improve the steering of my 2004 Yukon XL that had over 150,000 miles - trucks steering handles like it was new again - thanks Dave
verified_user Verified Buyer - David Proch - . MOOG moog-es3493t - 5 out of 5starstarstarstarstar" Review 1 Year Later "
Couldnt be happier with all the parts including this one I purchased to improve the steering of my 2004 Yukon XL that had over 150,000 miles - trucks steering handles like it was new again - thanks Dave
verified_user Verified Buyer - David Proch - . MOOG moog-es3493t - 5 out of 5question_answer Customer Questions and Answers
- Question:
- Are the outer tie rods pre-greased before being packaged?
- Answer:
- Moog-es3493t is greased after it is assembled. This is to preserve the part while it sits on the shelf. It must be greased after it is installed and every oil change with HD chassis grease with the NLGI certification.
- Question:
- How do I get the zerk fitting onto the tie rod? I've always purchased Moog products for my vehicles, but have never had this much trouble with a zerk fitting.
- Answer:
- Put a small amount of grease on the threads of the zerk. Put pressure on the top of the zerk and start to screw in. As soon as the zerk is tight stop. Do not over tighten or the zerk could break off in the part.
- Question:
- What is the difference between es3492T and es3493t for the vehicle 2001 GMC Sierra 1500?
- Answer:
- Differences are: es3493T Power Steering; Gear Steering; Problem Solver - Powdered Metal Gusher Brg. For Better Lubrication es3492T https://www.suspension.com/moog-es3492t Power Steering; Rack Steering; Problem Solver - Powdered Metal Gusher Brg. Fo or Better Lubrication ...see more
- Question:
- Will this part ES3493T fit a 2003 Silverado ss with a rough country leveling kit?
- Answer:
- If you currently have OEM tie rods the Moog tie rods should fit.