moog-k8607t | Front Lower Ball Joint | Dodge Ram 3500 | MOOG-K8607t

  • moog-k8607t 360image 1
  • moog-k8607t Front Lower Ball Joint
  • moog-k8607t Front Lower Ball Joint
  • moog-k8607t Front Lower Ball Joint
  • moog-k8607t Front Lower Ball Joint
  • moog-k8607t 360image large 1

Front Lower Ball Joint

Manufacturer: MOOG
Part Number: moog-k8607t
Price: $56.22

check_box In Stock check_box Ships Immediately


Suggested part for moog-k8607t: grease-gun-combo
grease-gun-combo Grease Gun and Multi-Purpose Grease - Fits Moog Zerk Fittings
MOOG parts come greased from the factory, but should also be greased at the time of installation. After installation, MOOG recommends greasing these parts at each oil change for the best service life.

Suggested part for moog-k8607t: mystik-jt6-hi-temp-multi-grease
mystik-jt6-hi-temp-multi-grease Mystik JT-6 High Temp Multi-Purpose Grease - 14 oz
Out of grease? No problem we've got you covered with this Mystik Multi-Purpose Grease tube refill.

  • Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.

    WARRANTY:

    Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.

    Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.

    If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.

    Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)

FitmentFront Lower Ball Joint moog-k8607t fits these vehicles:
Details

moog-k8607t | Front Lower Ball Joint | Dodge Ram 3500 | MOOG-K8607t

Enhanced Design Ball Joint. Fits Left or Right Side
Dodge 2500 models with a 4500 or 4850 lb Dana 60 axle only
  • Dodge 2500 with 4500 lb axle then you'll need a k80026
  • Dodge 2500 with 3500 or 3850 lb axle use k3134t
  • Dodge 2500 with Dana 44 axle use k8195t

Moog Problem Solver K8607T

OE Design Flaws

Vehicles that require the K8607T Front Lower ball joint are primarily used for heavy duty operations or are driven in harsh environments. The OE design for this ball joint is non-serviceable, meaning that if contaminants get into the part it cannot be flushed and you cannot add more grease if the ball joint loses lubrication.

Moog K8607T
Moog K8607T

Premium Moog design

Targeting factory defects and poor original design, Moog's Problem Solver K8607T Front Lower ball joint replaces the worn ball joint with a much more durable part. Moog has designed this ball joint by using a premium polychloroprene sealed boot and adding a zerk fitting, granting the ability to add grease to the part, allowing the user to flush out contaminants and keep the part lubricated.

Strength and durability

The K8607T ball joint, stocked in our Stephenville warehouse, uses a powdered-metal bearing instead of the usual plastic bearing, increasing the lifespan of the ball joint. The forged one-piece housing that Moog designed further enhances this ball joint's strength and durability. On top of that, the powdered-metal "gusher" bearing transfers vehicle loads through the ball joint and into the housing, reducing stress on the part itself.

Moog K8607T
Moog K8607T

Installation help

Adding to the difficulty of installation are multiple manufacturing variations with Straight-Axle and Twin I-Beam designs. As a result, installing the part incorrectly is an unfortunately common occurrence. Be sure to follow Moog's installation procedures for this part to avoid any problems. If you have any questions about the manufacturing variations or the K8607T Front Lower Ball joint please call the DST customer service team!

MOOG moog-k8607t

Product Reviews for moog-k8607t | Front Lower Ball Joint | Dodge Ram 3500 | MOOG-K8607t

5 Star (15)
100%
4 Star (0)
0%
3 Star (0)
0%
2 Star (0)
0%
1 Star (0)
0%
starstarstarstarstar

MOOG moog-k8607t

5 out of 5 based on 15 user reviews. Write a Review

J
verified_user

starstarstarstarstar" Solid Part and great fitment "

Good quality parts.

verified_user Verified Buyer - - . MOOG moog-k8607t - 5 out of 5
L
verified_user

starstarstarstarstar" Best money can buy! "

Love my moog parts, the new parts have made my 2003 excursion 7.3 diesel drive like new again! Thank you!

verified_user Verified Buyer - - . MOOG moog-k8607t - 5 out of 5
B
verified_user

starstarstarstarstar" Would highly recommend "

The parts that I ordered arrived in a timely fashion with everything needed to complete the install. All parts appeared to be of high quality and installed smoothly.

verified_user Verified Buyer - - . MOOG moog-k8607t - 5 out of 5
H
verified_user

starstarstarstarstar" Top Notch "

The parts were a great fit and are better than factory.

verified_user Verified Buyer - - . MOOG moog-k8607t - 5 out of 5

Fitment for moog-k8607t
MakeModelYear RangePositionDrive WheelQuantity RequiredEngine BaseEngine VINEngine Designation
DodgeRam 25001999-1994Front Lower4WD Quantity 2
DodgeRam 35001999-1994Front Lower4WD Quantity 2
DodgeRam 35001999-1994Front LowerRWD Quantity 2
FordExcursion2005-2000Front Lower4WD Quantity 2
FordF-250 Super Duty2016-1999Front Lower4WD Quantity 2
FordF-3501997-1992Front Lower4WD Quantity 2
FordF-350 Super Duty2016-1999Front Lower4WD Quantity 2

question_answer Customer Questions and Answers


Question:
Ordered front lower ball joints .Received K8607T . The one I received has rubber boot on the entire length of shaft and does not have a grease boot . I think this might be the wrong ball joint .
Answer:
You have the correct ball joint. Moog changed the design to an integral dust boot. It does not have the external dust boot any longer.

Question:
Does K8607T lower ball joint come with a separate boot or is the rubber extending up the stud the boot?
Answer:
Moog has changed the design of the ball joint and dust boots on some of their ball joints. moog-k8607t design has been changed to the intragral dust boot from the external dust boot.

Question:
What is the plastic or the plastic sleeve for the original does not have one should I take it off or leave it on.
Answer:
The plastic sleeve protects the ball joint stud from damage while it is sent to the customer.

Question:
I'm installing K8607T ball joints. It doesn't have a typical rubber dust cover, it is snuggly hugging the tapered part. Does it form a seal after it's installed and tightened? It doesn't look like the one on your website but google images will show pictures of what I'm talking about.
Answer:
Moog is in the process of redesigning the ball joint dust boots. It is called an integral dust boot. It seals much better that the external dust boot.

Question:
Was there a change to the dust boot on the K8607T ball joint?
Answer:
Yes Moog changed the design of the moog-k8607t ball joint dust boot. It did away with the external dust boot. Now it has an integral dust boot made into the ball joint.

Question:
Is the moog-k8607t sold as a single ball joint or a pair?
Answer:
The moog-k8607t is sold as a single unit.

Question:
What kind of grease do I use for part number k8607t?
Answer:
Part number k8607t calls for any type of chassis grease.

Question:
Does Moog make the adjustable ball joints for my 1996 dodge ram 3500 4x4 or just them standard ones like part number k8607t?
Answer:
No, Moog only makes the standard oe replacements for the 1996 dodge ram 3500 4x4.

Question:
Will the moog-k8607t fit for the 04 Dodge 3500?
Answer:
The moog-k8607t is not fitted for the 04 Dodge Ram 3500, the moog-k8607t will only fit for the 94-99. Moog offers a moog-k7467 for the gear steering 04 Ram 3500, and the moog-k7465 for the rack and pinion steering 04 Ram 3500.

Question:
Is there away to get just the grease zerk out of the moog-k8607t ball joint, I ordered from another dealer and hte part is missing the zerk.
Answer:
Moog does not sell just the grease zerks of their ball joints unfortunately, the grease zerk thread is at a 1/4-28 so you may be able to get a replacement at a local hardware store or a fastenal.

Question:
What is the significance of the small square opening on part number k8607t?
Answer:
The Square opening on part number k8607t on the boot is the grease relief valve.

Question:
Will part numbers K8607T and K6696 fit my 2001 Chevy 2500HD 2WD?
Answer:
For the 2001 Chevy 2500HD 2WD, part number K8607T will not fit, but the K6696 will fit.

Question:
I read about oversized ball joints to compensate for a hallowed out the hole. Is the number k8607t for that? or do you make one for that purpose? Apparently, the nut for my 2006 F-250 4X4 lower BJ backed off and hallowed out the hole on the diff housing
Answer:
Unfortunately, Moog does not make the oversizes ball joints that are fitted for your vehicle. The only option they are are the standard replacements. I do apologize for this inconvenience.

Question:
Warranty how long with these ball joints and how often to grease?
Answer:
Moog ball joints have a limited lifetime warranty that is handled by the Moog dealer you purchased from. All Moog greaseable must be greased after the are installed and every oil change with a HD chassis grease that has the NLGI rating.