moog-ds1237 | Front Right Outer Tie Rod | Jeep Wrangler | MOOG-DS1237

  • moog-ds1237 Outer Tie Rod End - Passenger Side
  • moog-ds1237 Outer Tie Rod End - Passenger Side

Outer Tie Rod End - Passenger Side

Manufacturer: MOOG
Part Number: moog-ds1237
Price: $209.40

check_box Free Shipping!check_box In Stock check_box Ships Immediately


  • Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.

    WARRANTY:

    Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.

    Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.

    If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.

    Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)

FitmentOuter Tie Rod End - Passenger Side moog-ds1237 fits these vehicles:
Details

moog-ds1237 | Front Right Outer Tie Rod | Jeep Wrangler | MOOG-DS1237

Passenger Side Only. This is the Large Connecting Tie Rod.

Moog Tie Rods

Connecting the Driver to the Vehicle

Tie rods are a crucial part of your steering system. When you turn your steering wheel the motion travels through the steering rack, through the tie rods, and finally through your steering arm or spindle. Without tie rods, you wouldn't be able to turn your car. This part is also incredibly important to your vehicle's alignment. If you replace your tie rods, make sure to get an alignment done immediately afterward.

Moog Tie Rod Box
Moog Tie Rod

Designed for Strength, Durability, and Longevity

Moog tie rods feature several differences from the OE. One of the more obvious differences is the overall design itself. Whereas many OE tie rods are two-piece assemblies, Moog's tie rods are forged one-piece units. This one-piece design reduces the chance of early wear, increasing the durability of the part as a whole. To protect your tie rod, Moog uses a neoprene-sealed rubber dust boot. This dust boot is resistant to both extreme temperatures and abrasion. The design for this rubber boot includes a small valve to allow for the flushing of old grease and contaminants. In addition to all these other features, Moog crafts their tie rod end using hardened full-ball metal studs. These hardened studs can stand up to much more than the OE, making the tie rod that much more dependable.

Fitment for moog-ds1237
MakeModelYear RangePositionDrive WheelQuantity RequiredEngine BaseEngine VINEngine Designation
JeepWrangler1995-1991Right Outer4WD Quantity 1

question_answer Customer Questions and Answers


Question:
Hi is the above part for Left hand Drive only or would it fit on my Right Hand Drive jeep?
Answer:
moog-ds1237 would not work for a RH drive Jeep. Moog only sells tie rods and drag links for LH drive Jeeps.

Question:
Is your drag link ds1237 stronger than a standard OEM?
Answer:
Moog Tie rod end is Patented cover plate design allows for tighter tolerances vs traditional designs for a more durable part. Yes, it will be stronger than OEM.

Question:
Will the moog-ds1237 come pre-greased?
Answer:
The moog-ds1237 will come pre-greased, but you will want to grease it upon installation and every oil change with a 100% synthetic or quality petroleum based grease.