moog-es3088s | Tie Rod End Adjusting Sleeve | Buick Skylark 1986-1998

  • moog-es3088s Front Tie Rod Adjusting Bolt

Front Tie Rod Adjusting Bolt

Manufacturer: MOOG
Part Number: moog-es3088s
Price: $18.08

check_box In Stock check_box Ships Immediately

  • Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.


    Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.

    Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.

    If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.

FitmentFront Tie Rod Adjusting Bolt moog-es3088s fits these vehicles:

moog-es3088s | Tie Rod End Adjusting Sleeve | Buick Skylark 1986-1998

Fits Left or Right Side. Problem solver fluted design avoids corrosion.
  • Problem Solver, Fluted design avoids corrosion

ES3088S was designed to channel out corrosive build up, easing installation and increasing the lifespan of the part.

ES3088S Image One

Moog Problem Solver: ES3088S

The Problem: I can't adjust the tie rod stud in my GM car

Excessive corrosion is likely in a 2 year old or older GM car. If the tie rod adjusting studs are corroded, it may prevent (or hinder) you from being able to set toe and straight steering during wheel alignment. This leaves you frustrated because what you thought would be just an alignment turns into needing to change adjusting studs. DST has the relief you need: Moog Problem Solver ES3088S.

ES3088S Image Three

The Solution: Moog's Problem Solver: ES3088S

Moog's line of problem solver parts target factory defects or poor original design, replacing them with a better more durable part. Moog Problem Solver ES3088S will allow you to get your GM vehicle back in alignment without breaking the bank or causing any more headaches.

ES3088S Image Two

Clean Tie Rod Threads While Being Installed

Designed into ES3088S are threads to clean the tie rod ends as they are being installed. Moog has engineered adjusting studs that channel out corrosive build up due to the flutes at both ends. Yellow zinc dichromate coating resists corrosion so that you may have a peace of mind about the Moog Problem Solver you bought from DST!

Installation Tips:

  • Inspect tie rods thoroughly and replace if necessary
  • Complete cleaning of tie rod cavity may be required if corrosion build up is severe
  • Use thread lubricant to ease installation
Fitment for moog-es3088s
MakeModelYear RangePositionDrive WheelQuantity RequiredEngine BaseEngine VINEngine Designation
BuickSkyhawk1989-1982 Quantity 2
BuickSkylark1998-1986 Quantity 2
BuickSomerset1987-1986 Quantity 2
BuickSomerset Regal1985 Quantity 2
CadillacCimarron1988-1982 Quantity 2
ChevroletBeretta1996-1987 Quantity 2
ChevroletCavalier1994-1982 Quantity 2
ChevroletCorsica1996-1987 Quantity 2
OldsmobileAchieva1998-1992 Quantity 2
OldsmobileCalais1987-1985 Quantity 2
OldsmobileCutlass Calais1991-1988 Quantity 2
OldsmobileFirenza1988-1982 Quantity 2
PontiacGrand Am1998-1985 Quantity 2
PontiacJ20001983-1982 Quantity 2
PontiacJ2000 Sunbird1985-1984 Quantity 2
PontiacSunbird1994-1986 Quantity 2
PontiacTempest1991-1987 Quantity 2