lock Warranty Information keyboard_arrow_down
Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.
Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.
Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.
If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.
Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)
Moog Tie Rods
Connecting the Driver to the Vehicle
Tie rods are a crucial part of your steering system. When you turn your steering wheel the motion travels through the steering rack, through the tie rods, and finally through your steering arm or spindle. Without tie rods, you wouldn't be able to turn your car. This part is also incredibly important to your vehicle's alignment. If you replace your tie rods, make sure to get an alignment done immediately afterward.
Designed for Strength, Durability, and Longevity
Moog tie rods feature several differences from the OE. One of the more obvious differences is the overall design itself. Whereas many OE tie rods are two-piece assemblies, Moog's tie rods are forged one-piece units. This one-piece design reduces the chance of early wear, increasing the durability of the part as a whole. To protect your tie rod, Moog uses a neoprene-sealed rubber dust boot. This dust boot is resistant to both extreme temperatures and abrasion. The design for this rubber boot includes a small valve to allow for the flushing of old grease and contaminants. In addition to all these other features, Moog crafts their tie rod end using hardened full-ball metal studs. These hardened studs can stand up to much more than the OE, making the tie rod that much more dependable.
Product Reviews for moog-es3238rl | Front Outer Tie Rod End | 93-02 Pontiac Firebird | MOOG
- 5 Star (2)
- 4 Star (1)
- 3 Star (0)
- 2 Star (0)
- 1 Star (0)
starstarstarstarstar_border" good compared to competition "
These worked fine for my 2001 Firebird Trans Am. They are much higher quality than the other replacements Ive tried. The only issue I have is the grease fitting did not want to thread in easily on one of the tie rods. other than that, high-quality pieces.verified_user Verified Buyer - Josh Whitmarsh - . MOOG moog-es3238rl - 4 out of 5
starstarstarstarstar" Excellent "
These Moog parts are THE ONLY ones I put on my 2002 FHP B4C. With the Z06 LS6 engine I need great handling and these parts provide that. So you better buy Moog or you could lose control.verified_user Verified Buyer - Peter B Gray - . MOOG moog-es3238rl - 5 out of 5
starstarstarstarstar" 5 Stars !!!! "
Truly what the doctor ordered. After 11 years of use, the old rubber tie rod ends have long since seen their better days. Your new polyurethane parts pulled my front end back together. It was easy to install and the alignment was easy and true. It was like night and day. Thank you for giving me back a safe car to drive.verified_user Verified Buyer - Emmitt D. Bass III - . MOOG moog-es3238rl - 5 out of 5
question_answer Customer Questions and Answers
- What are the stud thread and rack end threads on part number es3238rl?
- For part number es3238rl, both the stud thread and the rack end thread are M12 x 1.25.
- Does MOOG Tie Rod End Part # ES3238RL comes in a pair?
- moog-es3238rl tie rod is sold individually. Not in pairs.