• 9.13126 Front Ball Joint Dust Boots
  • 9.13126 Front Ball Joint Dust Boots
  • 9.13126 Front Ball Joint Dust Boots
  • 9.13126 Front Ball Joint Dust Boots

Front Ball Joint Dust Boots

Part Number: 9.13126
Manufacturer: Energy Suspension
Rating 14


Exclusive for DST Customers: (Learn More)
Free Lifetime Warranty Upgrade
Price: $6.75

In Stock Ships Immediately

Polyurethane Front Ball Joint Dust Boots
Finally, someone has made a replacement ball joint dust boot! No more expenseor cost worries when the boot wears out or is damaged either from installation or from day to day use.

Ball Joint Dust Boots - Chevrolet C1500 Pickup

Pin Opening Diameter Base Opening Diameter Height of Boot Piece Number
22.95mm (0.9 inch) 54mm (2.125 inch) 28mm (1.1 inch) 13013
16.2mm (0.635 inch) 41.0mm (1.615 inch) 28mm (1.1 inch) 13014
Here is our complete list of universal dust boots.
Polyurethane Front Ball Joint Dust Boots
  • Repair torn and worn out ball joint boots without having to buy the entire ball joint just to get the boot.
  • Adds both durability and that custom look attention custom show car builders!
  • Lasts longer, seals better and looks great for show vehicles!
  • Resist damage from rocks, sand, water, road salt, and oils better than many other O.E.M. rubber boots.
  • Made of Energy's HYPER FLEX performance polyurethane for added performance and durability.
  • One Set Will Cover the Left and Right Side
Energy Suspension Ball Joint Dust Boots are a exceptionally cost effective way to fix a torn or cracking OE dust boot. OE manufacturers will typically only sell you a replacement boot along with the entire ball joint. Energy Suspension Ball Joint Dust Boots will fix the same issue at a fraction of the cost of a new ball joint.

Part ImagePiece Number ↑(a) Pin Opening Diameter(b) Base DiameterHeight
Universal Dust Boot 130131301322.95 mm (0.9 inch)54 mm (2.125 inch)28 mm (1.1 inch)
Universal Dust Boot 130141301416.2 mm (0.635 inch)41.0 mm (1.615 inch)28 mm (1.1 inch)
  • 2 - 13013 Dust Boots
  • 2 - 13014 Dust Boots

 energy logoEnergy Suspension warrants its products against defects in workmanship and material for 24 months when used on passenger cars and light trucks. Products that have been abused, altered, or incorrectly installed are not covered. Energy Suspension will replace defective products or component parts, if inspection for factory personnel determines the part to be defective. Warranty replacement covers only the product. Labor claims, time loss, or freight charges will not be honored.
Alternate Part Numbers for 9.13126
  • ENE-9.13126G
  • ENE-9.13126R
  • ENS-9-13126G
  • ENS-9-13126R
  • 913126G
  • 913126R

Energy Suspension 9.13126

Product Reviews for Ball Joint Dust Boots 9.13126

Energy Suspension 9.13126

5 out of 5 based on 14 user reviews. Write a Review

These were used in a restoration of a heavily optioned 1960 Tbird. Not too sloppy, not too soft, not too long, and not too short. Just right.
5 out of 5 - PERFECT
jay smalley - . Energy Suspension 9.13126
Thanks for the follow up. Everything is working great.
5 out of 5 - Review 1 Year Later
William G Hughes - . Energy Suspension 9.13126
Very good.
5 out of 5 - Review 1 Year Later
donald sandidge - . Energy Suspension 9.13126
Still look great and no tears like the stock rubber boots had after about 6 months I was so mad when I replaced the ball joints only to have 3 out of 4 of the boots tear 6 months later driving in Utah winters. Ball joint boots are a must.
5 out of 5 - Review 1 Year Later
paul smits - . Energy Suspension 9.13126
So far so good.
5 out of 5 - Review 2 Years Later
Imon D. Crouse - . Energy Suspension 9.13126
When i replaced the ball joints on my truck the cups that came with them wouldnt seat correctly and ended up ripping before i could even get them on the truck. I considered going and getting replacements but knew i was going to have the same issue, so i decided to order these. They fit great, worked like they are supposed to, and saved me lots of time messing with the boots that came with the ball joints. If i have to replace ball joints again in the future i will make sure to order these and have them ready before starting the job
5 out of 5 - Worth Every Penny
Dan - . Energy Suspension 9.13126
The boots did just what I wanted. I used them on tie rod ends on a motorhome.
5 out of 5 - good quality
Phil Meraux - . Energy Suspension 9.13126
The parts arrived quickly and in the condition I expected. I actually bought this part to use one of the larger dust boots to re-assemble my 77 F-150 pitman arm to steering linkage connection. This was the only part that I could find that offered the correct dimensions I required to get the fit I was looking for. Pricing was good for the whole kit, so now I have some extra parts to upgrade other thrashed dust boots on my F-150.
5 out of 5 - Great Product
Chad Daigle - . Energy Suspension 9.13126
I bought these for a piece of heavy equipment that I was repairing. They fit correctly and worked out well saving me a lot of money over buying them from the equipment manufacturer.
5 out of 5 - worked well
joel d flickinger - . Energy Suspension 9.13126
I found the large diameter boots to be too big. The smaller boots fit the upper ball joints well. I ordered 5-13102s for the bottom. I have an after market mustang II frontend. I would suggest a kit with these two pair of boots together.
5 out of 5 - Great stuff
David Townsend - . Energy Suspension 9.13126
I ordered this set for one of the larger boots to replace a boot that I tore on the drag link of my P30 motor home chassis. The match was close, but a little large on the I.D. I did not see a listing for the exact part. Although not optimal, the boot will do the job.
5 out of 5 - Great products.
Scott - . Energy Suspension 9.13126
It took some time to isolate each ball joint but once isolated, it was a breeze putting these on. This saved so much money I cant say enough about them. It's been well over a month now and everything is fit and tight. Thanks for having these available. In so many words: PRICELESS!
5 out of 5 - great! saved a lot of money using these. thanks!
Albert Green - . Energy Suspension 9.13126
I couldn't get the upper ball joint boots to fit on my upper ball joints. They were some Parts Master ball joints that I got from Bumper to Bumper. I ended up getting some new upper ball joints and got some premium ones (and made in America) this time. I was able to use the lower ball joint boots on my lower ball joints. I guess they were designed to replace the ball joint boots on the original ball joints and wont necessarily work on every after-market ball joint. They probably cant keep up with every ball joint configuration that other manufacturers use.
4 out of 5 - Not for all ball joints
Steven Dupre - . Energy Suspension 9.13126
I used this for the 98-02 Ford Crown Victoria Idler Arm and it works great. Flawless.
5 out of 5 - Flawless!
Thomas Pearson - . Energy Suspension 9.13126