Energy Suspension Universal Tie Rod and Ball Joint Boots

energy suspension tie rod and ball joint boots Energy Suspension uses Hyperflex Polyurethane in their aftermarket replacement dust boots which makes them more resistant to wear than the stock dust boots.

Energy Suspension's polyurethane Tie Rod and Ball Joint Boots will protect those articulating suspension components from dirt, grime, and moisture and prevent grease from escaping longer than the stock boots. Find dust boots by dimension below.

Dust Boots are a small, simple part of a tie rod end or ball joint that covers the space where the stud exits the housing. This keeps grease inside the component and everything else out, but the original boots are made of rubber which can wear down or crack making the boot ineffective. This can allow contaminates to enter the bearing of ball joints or tie rod ends and cause wear or corrosion, reducing the lifespan of those parts.

Energy Suspension uses Hyperflex Polyurethane in their aftermarket replacement dust boots which makes them more resistant to wear than the stock dust boots. These boots are perfect for off-road vehicles that throw a lot of mud or put their ball joints in extreme situations. Poly boots are equally good for daily drivers that spend a lot of time on icy roads since they won't degrade when exposed to road salt, engine fluids, grime, or other elements that can break rubber down faster than normal wear. If you need to replace a dust boot on your tie rod or ball joint, or want to preemptively upgrade to a longer lasting part, then Energy Suspension is a great option.


How To Measure For Dust Boots

Measuring for Dust Boots

universal dust boot mounting diagram

Measure your Tie Rod End or Ball Joint to find the exact dust boot that will fit your part.

  • Dimensions A and B: The polyurethane is flexible and will stretch slightly. Energy Suspension's recommendation appears to be to use a part that is approx 0.5-1.0 mm smaller than the diameter you need. Example: If your OEM part measures 12mm then you would use a boot approx 11.5mm - 11mm in diameter at that dimension. This ensures a good tight fit that will seal correctly.
  • Height Dimension: Proper Height will ensure the boot stays seated when installed. It is a measurement of the entire boot, top to bottom.

Image Piece Number Included in Sets (a) Pin Opening Diameter (b) Base Opening Diameter Height of Boot
universal dust boot 13001 13001 9.13101 - Qty 2
9.13128 - Qty 2
16.13101 - Qty 2
9.13107 - Qty 12
9.13113 - Qty 50
14 mm (0.55 inch) 34.55 mm (1.36 inch) 25.25 mm (0.995 inch)
Energy Suspension 9.13102 - Tie Rod Dust Boots 13002
Octagon
9.13102 - Qty 2
9.13108 - Qty 12
9.13114 - Qty 50
14mm (0.55 inches) 34.55mm (1.36 inches) 25.25mm (0.99 inches)
universal dust boot 13003 13003 9.13103 - Qty 2
9.13109 - Qty 12
9.13115 - Qty 50
16.13101 - Qty 2
16.13102 - Qty 2
11.55 mm (0.455 inch) 30.5 mm (1.20 inch) 24 mm (0.945 inch)
Energy Suspension 9.13104 - Tie Rod Dust Boots 13004
Octagon
9.13104 - Qty 2 11.55 mm (0.455 inch) 30.5 mm (1.20 inch) 24 mm (0.945 inch)
universal dust boot 13005 13005 9.13105 - Qty 2
9.13111 - Qty 12
9.13117 - Qty 50
16.13102 - Qty 2
13 mm (0.511 inch) 36.35 mm (1.43 inch) 24 mm (0.945 inch)
Energy Suspension 9.13106 - Tie Rod Dust Boots 13006
Octagon
9.13106 - Qty 2 13 mm (0.511 inch) 36.35 mm (1.43 inch) 24 mm (0.945 inch)
universal dust boot 13007 13007 9.13119 - Qty 2
9.13121 - Qty 12
9.13123 - Qty 50
9.13128 - Qty 2
16.25 mm (0.64 inch) 41 mm (1.615 inch) 24.15 mm (0.95 inch)
Energy Suspension 9.13120 - Tie Rod Dust Boots 13020
Octagon
9.13120 - Qty 2 16.25 mm (0.64 inch) 41 mm (1.615 inch) 24.15 mm (0.95 inch)
universal dust boot 13009 13009 5.13102 - Qty 2
9.13125 - Qty 2
9.13130 - Qty 2
9.13132 - Qty 2
18.55 mm (0.73 inch) 41.25 mm (1.625 inch) 27.75 mm (1.092 inch)
universal dust boot 13010 13010 9.13127 - Qty 2
9.13125 - Qty 2
14.75 mm (0.580 inch) 36.25 mm (1.425 inch) 35.15 mm (1.385 inch)
universal dust boot 13013 13013 9.13126 - Qty 2 22.95 mm (0.9 inch) 54 mm (2.125 inch) 28 mm (1.1 inch)
universal dust boot 13014 13014 9.13131- Qty 2
9.13126 - Qty 2
9.13127 - Qty 2
9.13132 - Qty 2
16.2 mm (0.635 inch) 41.0 mm (1.615 inch) 28 mm (1.1 inch)
universal dust boot 13022 13022 5.13101 - Qty 2 21.5 mm (0.845 inch) 42.75 mm (1.685 inch) 55.9 mm (2.2 inch)
universal dust boot 13024 13024 5.13102 - Qty 2 16.3 mm (0.64 inch) 41.25 mm (1.625 inch) 36.7 mm (1.445 inch)
universal dust boot 13025 13025 9.13136 - Qty 2
13025 - Qty 1
19 mm (0.75 inch) 45.10 mm (1.775 inch) 42.33 mm (1.666 inch)
universal dust boot 13026 13026 9.13136 - Qty 2
13026 - Qty 1
21.25 mm (0.836 inch) 51 mm (2 inch) 40.3 mm (1.585 inch)

Energy Suspension's Limited Universal Dust Boot Listings are Shown Below:

Image Minimum Outer Diameter Minimum Outer Diameter Round Style Octagon Style
universal dust boot 13001 19/32" (0.590") - 15mm 1-3/8" (1.375") - 35mm 9.13101 9.13102
universal dust boot 13003 31/64" (0.472") - 12mm 1-13/64" (1.200") - 30.5mm 9.13103 913104
universal dust boot 13005 9/16" (0.550") - 14mm 1-7/16" (1.437") - 36.5mm 9.13105 9.13106
universal dust boot 13007 21/32" (0.650") - 16.6mm 1-5/8" (1.625") - 41.3mm 9.13119 9.13120
- 21/32" (0.650") - 16.6mm 1-5/8" (1.625") - 41.3mm 90.13119 - HD -
- 1-3/16" (1.187") - 30mm 1-7/8" (1.875") - 47mm 90.13127 - HD -