Energy Suspension CAMAROFIREBIRDREARSBB-82-02 Rear Sway Bar Bushings

  • camarofirebirdrearsbb-82-02 Rear Sway Bar Bushings

Rear Sway Bar Bushings

Manufacturer: Energy Suspension
Part Number: camarofirebirdrearsbb-82-02
:(?)

:(?)
Black
Red

:(?)
Free Lifetime Warranty Upgrade
Price: $0.01

check_box In Stock check_box Ships Immediately


  • 3.5161 19mm (0.74 inch)
  • 3.5145 21mm (0.82 inch)
  • 3.5146 23 mm (0.90 inch)
  • 3.5147 24 mm (0.94 inch)
Suggested part for camarofirebirdrearsbb-82-02: 9.11110
9.11110 Formula 5 Prelube 3 - 5 mL Tubes
Energy Suspension provides grease to install these parts, but you can never have too much. Grab an extra 3-pack of grease so you can more liberally apply grease when installing.

Suggested part for camarofirebirdrearsbb-82-02: DLL120
DLL120 Front Sway Bar Lateral Locks - 19-20mm
DST's lateral locks prevent sway bar movement and fits OE and aftermarket bars.

Suggested part for camarofirebirdrearsbb-82-02: DLL122
DLL122 Front Sway Bar Lateral Locks - 21-22mm
DST's lateral locks prevent sway bar movement and fits OE and aftermarket bars.

Suggested part for camarofirebirdrearsbb-82-02: DLL124
DLL124 Front Sway Bar Lateral Locks - 23-24mm
DST's lateral locks prevent sway bar movement and fits OE and aftermarket bars.

  • Energy Suspension warrants its products against defects in workmanship and material for 24 months when used on passenger cars and light trucks. Products that have been abused, altered, or incorrectly installed are not covered. Energy Suspension will replace defective products or component parts, if inspection for factory personnel determines the part to be defective. Warranty replacement covers only the product. Labor claims, time loss, or freight charges will not be honored.
FitmentRear Sway Bar Bushings camarofirebirdrearsbb-82-02 fits these vehicles:
Details
Polyurethane Rear Sway Bar Bushings
Improved handling, low cost, and easy installation are just some of the reasons these components are so popular!

There are a number of different size rear sway bars in this vehicle.
The ONLY way to ensure you're buying the correct size bushings for your car is to actually physically measure the sway bar. The is most commonly done one of two ways.

- 1 - Wrench method. This is quite simple - just take a set of wrenches and see which one fits over the bar correctly. For example - if a 18mm wrench fits perfectly over your sway bar - then you have an 18mm sway bar! Not all of us are lucky enough to be able to us this method as there are at times mid-sizes like 23.5mm etc. See below if you fall into this category.

- 2 - Crescent Wrench Method. Just a little more complex than the wrench method. Simply tighten down your adjustable crescent wrench down over your sway bar. When it's tight - slip the wrench off and measure between the ends of the prongs. The distance between these is the size of your sway bar.

Buying the correct size bushings is VITAL to ensuring optimum performance from your sway bar. Bushings that are too large will not properly grip and support the sway bar. Likewise bushings that are too small may simply not fit over the bar and make installation impossible.


1982 - 2002 Camaro / Firebird / Trans Am Rear Sway Bar Bushings
�Bar Diameter �Part Number
19mm 35161
21mm 35145
23mm 35146
24mm 35147
Polyurethane Rear Sway Bar Bushings
  • Your vehicle's sway bar system will work at its maximum efficiency!
  • Replaces that original, short lived and too-soft rubber.
  • Easy to install with basic tools.
  • Made of rugged Energy's HYPERFLEX performance polyurethane material and the hardware is heavy duty for lasting durability.
Footnotes
  • One Set Will Cover the Left and Right Side

Energy Suspension Sway Bar Bushings

Energy Suspension Hyperflex Sway Bar bushings are made of polyurethane, which is a much more durable material for suspension bushings than rubber. Polyurethane does not break down due to road grime, weather or oils the way the rubber can. Have the peace of mind knowing you have a long lasting part on your sway bar with Energy Suspension's sway bar bushings. Energy Suspension's polyurethane sway bar bushings provide a secure grip on the sway bar and do not warp over time. With this snug grip, your vehicle will see a performance boost similar to installing a larger sway bar.

Energy Sway Bar Bushing
Faulty Rubber

Faulty Rubber

A sway bar's function is to maintain the maximum amount of road contact during tires. The sway bar is held to the frame of the vehicle with a sway bar bushing. Original Equipment rubber can warp and/or crack, losing its grip on the bar. This causes your sway bar to lose its effectiveness. Just look at the old rubber sway bar bushing to the left. Imagine how good of a grip that thing could keep on a sway bar. Go with Polyurethane.

Be sure to use Formula 5

The sway bar bushing sees a lot of action, so make sure you grease it well with Energy Suspension's own Formula 5 Bushing Lubricant. Using plenty of grease is the best way to ensure a long lasting part without any squeaking. If you'd like some extra grease just in case, pick up an extra 3 pack or an 8 ounce tube.

Formula 5 Gif

question_answer Customer Questions and Answers


Question:
Do the rear sway bar bushings come with end links in the kit camarofirebirdrearsbb-82-02?
Answer:
Yes, the end links do come with the parts in the kit.